Master Vapor Pump 150
$21,330.63
The MVP 150 is a certified LP-Gas recovery pump specifically designed for Butane, Butane/Propane, or pure Propane vapor recovery. The motor is Explosion-proof and rated for C1D1 areas.
It is available in both three-phase and single-phase models and can operate 24/7 without the need for an air compressor. CO2 gas is used to charge the pump-head and must be supplied by the operator.
Description
- Certified positive displacement LP-Gas extraction pump
- Electric powered double diaphragm gas compressor
- Explosion-proof motor rated for C1D1 areas
- Continuous 100% duty cycle – run 24/7
- No air compressor needed
- Can pull vacuum back through pump when evacuating system
- Patented pump drive technology
- No rotating or moving seals
- Can run dry without damage
- Can stall under pressure without damage
- Can start against full load and pressure
- Maximum pumping pressure output is adjustable
- No lubrication in pump heads, no contamination of product
- Meets NFPA 58 requirements for LP-Gas – rated LPG 350 PSI
- Meets Class 1 Division 1 Hazardous area facility requirements (when installed correctly)
- Easy DIY diaphragm replacement or internal cleaning when needed
- Simple stainless steel reed valve replacement if ever needed
- One year manufacturer’s warranty
- Made in USA
- Recover LP-Gas vapor at over 6 CFM (cubic feet per minute)
- Recover butane at up to 1 LB/MIN (pounds per minute)
- Recover and re-condense butane at OVER 12 GPH (gallons per hThe)
- Maximum pumping outlet pressure: 60 PSI (4.1 bar) continuous; 70 PSI (4.8 bar) intermittent
- Maximum pumping inlet vacuum produced: 27 InHG (0.91 bar)
- Maximum pumping speed: 190 CPM (cycles per minute)
- Pump static withstand pressure rating: MAWP 350 PSI (24 bar)
- Materials: pressure section; stainless steel, diaphragms; FKM, reed valves; stainless steel
- Process gas temperature range: FKM -40 to 275°F (-40 to 135°C)
- Recommended FKM replacement schedule: every 1,000 hThes
- Air temperature range for motor/gearbox operation: 32 to 105°F (0 to 40°C)
- Motor is coupled to diaphragms with patented gas pressure-charged chamber
- Pumping outlet pressure runs about 10 PSI lower than the charge gas pressure level
- Non-reactive CO2 gas is used to charge the pump head
- CO2 gas is safer than air for driving the pump
- CO2 gas is non-flammable and non-explosive with LPG (should a diaphragm ever leak)
- CO2 gas regulator with gauges is provided with pump assembly
- CO2 tank is operator provided and available at any welding supply store
- Pump charge gas supply: standard (20#) 5 LB tank of industrial CO2
- Typical CO2 gas usage: <0.2 SCFH (very little); estimated life of charge gas tank is 1 year
- Pump charge gas pressure range: continuous 5 to 70 PSI (1.4 to 5.5 bar); to 80 PSI intermittent
- Electric motor: explosion-proof for C1D1 hazardous areas; rated Class I Gr C & D, Class II Gr F&G
- Electric motor: 1 HP, 1800 RM, 60 Hz
- Motor Option 1: Model MVP-6CFM-1PH; Single-phase 115/208-230V, 13.4/6.7 FLA (full load amps)
- Motor Option 2: Model MVP-6CFM-3PH; Three-phase 208-230/460V, 3.3/1.65 FLA (full load amps), Inverter-rated
- Pump speed: 190 CPM (cycles per minute) at 60 Hz
- Noise: sound pressure measured 1 meter from pump; 80.5 dBA
- Process inlet & outlet: 1/2″ JIC-male
- Added ports for optional pressure gauges: inlet & outlet 1/4″ FNPT
- Inlet & outlet ports at ideal equipment connection heights of 46″ and 41″ above floor
- Size: 17″ x 19.9″ bas x 46″ tall
- Weight: 182.5 lbs (82.8 kg)
